Effect of the grain size on the macroscopic response of aluminum to shock loading

Shock tests of two lots of a 1420 aluminum-lithium alloy are performed. The mean grain size is 24 μm in the first lot and 1.6 μm in the second lot obtained by the method of equal-channel angular pressing. Two characteristics of dynamic strength of the material were determined in experiments on the high-velocity impact of flat samples: threshold of dynamic stability with respect to compression on the fore front of the compression pulse and spall strength of the material. The materials of both types have an identical threshold of dynamic stability with respect to compression, whereas the spall strength of the microcrystalline alloy is 20% greater than the spall strength of the polycrystalline alloy. The reason is the consumption of energy on structure formation in the coarse-grain material in passing to a larger-scale structural level (in the case with a fine-grain material, such a structure is available in the initial state). The experiments reveal the presence of a second plastic front whose amplitude is approximately 10% of the first plastic front. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 6, pp. 135–146, November–December, 2007.     

Effect of a Nanoclay on the Mechanical,Thermal and Flame Retardant Properties of Rigid Polyurethane Foam

Water blown rigid polyurethane foams (PUF) with organoclay/organically modified nanoclay (ONC) were prepared and their properties such as density, mechanical, morphological, insulation, thermal and flame retardant properties were studied. In this investigation, the ONC content was varied from 1 to 10 parts per hundred of polyol (php) by weight. It was observed that the compressive strength of ONC filled PUF increased up to 3 php of ONC loading and then it decreased. Wide angle X-ray diffraction and transmission electron microscopy studies indicated the exfoliated dispersion of ONC in PUF. The thermal conductivity of ONC filled PUF decreases up to 5 php and then increases. The glass transition temperature (Tg) of PUF decreases on loading of ONC. The TGA analysis shows that there is slight increase in degradation temperature with increase in ONC loading. The flame retardant properties (LOI and flame spread rate) are improved slightly on addition (3 php) of ONC filled PUF.     

K9光学玻璃化学钢化技术研究

为提高K9光学玻璃在一些特殊应用领域（如高压、温度变化剧烈等）的力学性能,并保证其光学性能符合精密光学仪器要求,对K9光学玻璃进行了化学钢化技术研究。以脆性材料断裂过程微裂纹扩展理论为基础,导出化学钢化玻璃强度应力因子计算模型,分析化学钢化表面应力与表面微裂纹深度、韧性之间的关系,指出化学钢化工艺应注意的事项。通过实验研究,分析化学钢化温度和钢化时间对K9光学玻璃抗弯强度、表面应力及应力层厚度的影响,优化得出K9光学玻璃化学钢化温度为400 ℃、钢化时间为40 h。采用优化工艺,获得了表面应力为500 MPa、应力层厚度为50 μm量级及规格为220 mm×110 mm×22 mm的化学钢化K9光学玻璃样件。钢化后,样件抗弯强度提高了3.5倍以上,且表面疵病、光学鉴别率、透过率等光学性能指标未见明显变化。     

The role of the bubble–bubble interaction on radial pulsations of bubbles

Using a model that with or without considering the interaction between bubbles through the radiated pressure waves, numerical simulations of cavitation bubbles have been performed in order to study the effect of the bubble–bubble interaction on radial pulsations of bubbles. Comparing the results obtained by with or without considering the bubble–bubble interaction, it is suggested that the suppression or enlargement property of expansion ratios of bubbles due to the bubble–bubble interaction largely depends on the ultrasound parameters, the ambient bubble radii, the distances between bubbles and the number of bubbles (in multi-bubble environment, the last two aspects can be expressed using the coupling strength). The frequency response curve of expansion ratio decreases and shifts to left due to the bubble–bubble interaction and the larger the coupling strength is, the more the left-shifting is.     

INFLUENCE OF SHAMPOO ON THE MECHANICAL PROPERTIES OF HUMAN HAIRS1)

头发的弹性和抵抗意外拉断的能力是人们非常关注的指标。为了迎合这一需求,有些厂商推出了具有所谓“强韧”发质功效的洗发水,但其实并不清楚是否真能使头发变“强韧”。为此,针对市场上常见的一种标称具有“强韧”功效的洗发水,通过拉伸力学实验对头发洗护前后的力学性能进行了对比研究。结果表明,用洗发水处理后的头发,屈服应力下降,意味着头发更容易过早进入塑性变形;抗拉强度、最大应变减小,意味着头发抵抗外力拉断的能力下降;杨氏模量下降,说明头发抵抗弹性变形的能力变差。综上,所研究的洗发水对“强韧”发质没有帮助。 关键词: 头发,洗发水,力学性能,强度,韧性     

考虑塑性变形发展程度系数的RC梁开裂弯矩改进计算公式

针对RC梁开裂荷载计算方法尚未统一的现状，首先，结合18根RC梁试验数据对比了已有的6种RC梁开裂弯矩计算公式，发现开裂弯矩理论计算值与试验值的偏差大小和混凝土强度有关；然后，通过提出塑性变形发展程度系数k，推导新的RC梁开裂弯矩计算公式，并进一步基于k值和塑性影响系数计算值γ_k进行改进；最后，选取12根RC试验梁验证改进公式的准确性，证明改进公式的计算值与试验值吻合更好且偏于安全。     

Electric field‐induced birefringence,optical rotatory power and conoscopic measurements of a chiral antiferroelectric smectic liquid crystal

Using a photoelastic modulator‐based novel set‐up, the electric field‐induced in‐plane birefringence and the optical rotatory power (ORP) were measured of an antiferroelectric liquid crystalline compound (12OF1M7) in its various phases using 30 µm homeotropic cells. Some specific signatures of the in‐plane birefringence and of the ORP for the various phases are being established. A relatively small threshold field is needed for the unwinding process of the antiferroelectric phase with a unit cell of four layers [SmC_A*(1/2)] compared with that for two layers [SmC_A*(0)]. On application of the electric field on the high temperature side of the SmC_A*(1/2) phase (80.1–81.5°C), a field‐induced phase transition is shown to occur directly to the SmC* phase, whereas on the lower temperature side (79.4–80.1°C) the transition takes place to SmC* via the SmC_A*(1/3) phase. The in‐plane birefringence exhibits a critical power law dependence for the SmC*–SmA transition. The ORP changes sign within the temperature range of the phase with a unit cell of three layers, reflecting a change in the handedness during this phase. Using tilted conoscopy, the results for the biaxiality and the apparent tilt angle for a smectic liquid crystal with a tilt angle greater than 18° in the ferroelectric phase are reported. The biaxiality implies the difference in the refractive indices between the two minor axes of the refractive index ellipsoid. The optical transmittance at visible and IR wavelengths for free‐standing films reveal characteristic reflection bands for these phases. The modulated structures of the reflected bands appear just above the SmC_A* phase and below SmC_A*(1/3); these are possibly due to an easy deformation of the phase by the surfaces.     

The dependence of structure and properties of polycrystalline diamonds (PCD) on the conditions of their production

Abstract

AES and SIMS were used to analyze the diamond powders surface composition using LAS-3000 device. It is found that impurities on diamond particles surfaces have a detrimental effect on the PCD sintering and physico-mechanical properties of the product.     

Photosensitivity,substituent and solvent-induced shifts in UV-visible absorption bands of naphthyl-ester liquid crystals: a comparative theoretical approach

The substituent- and solvent-induced shifts in UV-visible absorption bands of naphthyl-ester nematic liquid crystals, viz., 4-octylphenyl-6-octyloxy-2-naphthoate (NAPHE1) and 6-octyloxy-2-naphthylyl-4-octyloxybenzoate (NAPHE2), have been investigated using the DFT, CNDO/S and INDO/S methods. A correlation has been made between molecular charge distribution and phase stability based on Mulliken, Loewdin, AM1, PM3, MNDO, CNDO/S and INDO/S methods. The observed π→π* and n→π* electronic transitions have been reported. The substituent- and solvent-induced shifts in absorption bands, transition energies and energy gaps have been discussed. The photosensitivity of the molecules has been analysed based on these shifts. It has been observed that the substituent has a dominant role on both absorption maxima and energy band gap, whereas the solvent has a dominant role only on absorption maxima, and no effect has been observed on the energy gap. These shifts may provide beneficial consequences in determining the end use of compounds.     

Role of weak interface to retain high strength of fiber in monofilamentary SiC fiber/titanium-aluminide composite

The tensile strength of monofilamentary weakly bonded SiC fiber/γ-TiAl intermetallic compound matrix composite, prepared by the sputtering method, was measured and analysed using a fracture mechanical technique. The main results are summarized as follows: (1) The fracture of TiAl occurred prior to that of fiber, resulting in formation of circumferential cracks on the fiber. Interfacial debonding occurred during tensile test, resulting in long pull-out of the fiber. (2) The strength of the fiber in the TiAl matrix was nearly the same as that of the bare fiber. (3) The fracture mechanical analysis showed that (i) the interfacial debonding grows unstably upon initiation and (ii) the stress distribution in the fiber in the cross-section, where the matrix is fractured, approaches to that of bare fiber with increasing debonded length. The reason why the fiber strength was maintained in spite of the formation of cracks on the fiber surface due to the premature fracture of the matrix was accounted for by the fully blunted crack-tip from the above calculation result.